欢迎光临
我们一直在努力

8*8点阵 16*16点阵 级联模块 示例教程 适用于Arduino平台

视频教程讲解:觉得不清楚的点传送门观看1080P版

1. 产品图片

2. 产品购买地址点我购买

3. 产品概述
8*8点阵由64个发光二极管组成,按照传统的矩阵扫描方式,64个发光二极管至少需要16个IO口才能操作。于是我们引入了MAX7219驱动芯片,它通过16位数据串行输入输出方式完成控制64个LED,全程仅需3个IO口。

4. 产品参数
单个模块可以驱动一个8*8共阴点阵
模块工作电压:5V
模块尺寸:长5厘米X宽3.2厘米X高1.5厘米
带4个固定螺丝孔,孔径3mm,可使用本店M3铜柱固定
模块带输入输出接口,支持多个模块级联

5. 使用方式
模块左边为输入端口,右边为输出端口。
控制单个模块时,只需要将输入端口接到CPU
多个模块级联时,第1个模块的输入端接CPU,输出端接第2个模块的输入端,第2个模块的输出端接第3个模块的输入端,以此类推。

6. 接线方式
VCC 接 5V
GND 接 GND
DIN 接 pin5
CS 接 pin4
CLK 接pin3

7. 示例程序一

//中贝斯特UltiRobot88点阵模块示例教程
//程序效果:依次显示0-9,A-Z,中、国字样。
//淘宝店地址:zhongbest.taobao.com
//专业Arduino资料网站:www.arduino365.com

int clk =3;
int cs=4;
int din=5;
unsigned char disp1[38][8]={
{0x3C,0x42,0x42,0x42,0x42,0x42,0x42,0x3C},//0
{0x10,0x18,0x14,0x10,0x10,0x10,0x10,0x10},//1
{0x7E,0x2,0x2,0x7E,0x40,0x40,0x40,0x7E},//2
{0x3E,0x2,0x2,0x3E,0x2,0x2,0x3E,0x0},//3
{0x8,0x18,0x28,0x48,0xFE,0x8,0x8,0x8},//4
{0x3C,0x20,0x20,0x3C,0x4,0x4,0x3C,0x0},//5
{0x3C,0x20,0x20,0x3C,0x24,0x24,0x3C,0x0},//6
{0x3E,0x22,0x4,0x8,0x8,0x8,0x8,0x8},//7
{0x0,0x3E,0x22,0x22,0x3E,0x22,0x22,0x3E},//8
{0x3E,0x22,0x22,0x3E,0x2,0x2,0x2,0x3E},//9
{0x8,0x14,0x22,0x3E,0x22,0x22,0x22,0x22},//A
{0x3C,0x22,0x22,0x3E,0x22,0x22,0x3C,0x0},//B
{0x3C,0x40,0x40,0x40,0x40,0x40,0x3C,0x0},//C
{0x7C,0x42,0x42,0x42,0x42,0x42,0x7C,0x0},//D
{0x7C,0x40,0x40,0x7C,0x40,0x40,0x40,0x7C},//E
{0x7C,0x40,0x40,0x7C,0x40,0x40,0x40,0x40},//F
{0x3C,0x40,0x40,0x40,0x40,0x44,0x44,0x3C},//G
{0x44,0x44,0x44,0x7C,0x44,0x44,0x44,0x44},//H
{0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x7C},//I
{0x3C,0x8,0x8,0x8,0x8,0x8,0x48,0x30},//J
{0x0,0x24,0x28,0x30,0x20,0x30,0x28,0x24},//K
{0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x7C},//L
{0x81,0xC3,0xA5,0x99,0x81,0x81,0x81,0x81},//M
{0x0,0x42,0x62,0x52,0x4A,0x46,0x42,0x0},//N
{0x3C,0x42,0x42,0x42,0x42,0x42,0x42,0x3C},//O
{0x3C,0x22,0x22,0x22,0x3C,0x20,0x20,0x20},//P
{0x1C,0x22,0x22,0x22,0x22,0x26,0x22,0x1D},//Q
{0x3C,0x22,0x22,0x22,0x3C,0x24,0x22,0x21},//R
{0x0,0x1E,0x20,0x20,0x3E,0x2,0x2,0x3C},//S
{0x0,0x3E,0x8,0x8,0x8,0x8,0x8,0x8},//T
{0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1C},//U
{0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18},//V
{0x0,0x49,0x49,0x49,0x49,0x2A,0x1C,0x0},//W
{0x0,0x41,0x22,0x14,0x8,0x14,0x22,0x41},//X
{0x41,0x22,0x14,0x8,0x8,0x8,0x8,0x8},//Y
{0x0,0x7F,0x2,0x4,0x8,0x10,0x20,0x7F},//Z
{0x8,0x7F,0x49,0x49,0x7F,0x8,0x8,0x8},//中
{0x7F,0x41,0x49,0x49,0x49,0x8,0x14,0x63},//国
};

void setup(){
  pinMode(cs,OUTPUT);
  pinMode(clk,OUTPUT);
  pinMode(din,OUTPUT);
  Init_MAX7219();
}
void loop(){
  char i,j;
//Write_Max7219(0x0f, 0x00); 
//Delay_xms(500);

  for(j=0;j<38;j++)
  {
   for(i=1;i<9;i++)
    Write_Max7219(i,disp1[j][i-1]);
   delay(500);
  } 

}

void Write_Max7219_byte(char DATA)         
{
            char i;    
                digitalWrite(cs,0);                
            for(i=8;i>=1;i--)
          {                  
           digitalWrite(clk,0);
            if((DATA&0x80)>0){digitalWrite(din,1);}
            else{digitalWrite(din,0);}
            //提取最高位给DIN端口
            DATA=DATA<<1;//左移一位
            digitalWrite(clk,1);
           }                                 
}
void Write_Max7219(char address,char dat)
{ 
         digitalWrite(cs,0);
         Write_Max7219_byte(address);           //写入地址,即数码管编号
     Write_Max7219_byte(dat);               //写入数据,即数码管显示数字 
         digitalWrite(cs,1);                        
}
void Init_MAX7219(void)
{
Write_Max7219(0x09, 0x00);//译码方式:BCD码
Write_Max7219(0x0a, 0x01);//亮度 
Write_Max7219(0x0b, 0x07); //扫描界限;8个数码管显示
Write_Max7219(0x0c, 0x01);  //掉电模式:0,普通模式:1
Write_Max7219(0x0f, 0x00);
delay(500); //显示测试:1;测试结束,正常显示:0
}

8. 示例程序二
由于市面上没有级联教程,所以就想起来写了个,按照类推方式应该可以组任意多个矩阵。

//中贝斯特UltiRobot88点阵模块示例教程
//程序效果:四个88点阵模块级联,组成一个1616模块,循环播放:中贝斯特
//淘宝店地址:zhongbest.taobao.com
//专业Arduino资料网站:www.arduino365.com
int clk =3;
int cs=4;
int din=5;
unsigned char disp3[4][8]={
{0x80,0x80,0x80,0x80,0xFC,0x84,0x84,0x84},//中
{0x00,0xF8,0x08,0x08,0x08,0x88,0x88,0x88},//贝
{0x00,0x02,0xBC,0x20,0x20,0x20,0x3E,0x24},//斯
{0x10,0x10,0x10,0xFE,0x10,0x10,0xFE,0x04},//特
};

unsigned char disp1[4][8]={
{0x84,0x84,0xFC,0x84,0x80,0x80,0x80,0x80},//中
{0x88,0x88,0x08,0x40,0x20,0x10,0x08,0x04},//贝
{0x24,0x24,0x24,0xA4,0x24,0x44,0xC4,0x84},//斯
{0x04,0xFE,0x04,0x44,0x24,0x04,0x14,0x08},//特
};

unsigned char disp4[4][8]={
{0x00,0x00,0x00,0x00,0x1F,0x10,0x10,0x10},//中
{0x00,0x0F,0x08,0x08,0x08,0x08,0x08,0x08},//贝
{0x11,0x11,0x3F,0x11,0x11,0x1F,0x11,0x11},//斯
{0x08,0x08,0x28,0x28,0x3E,0x28,0x49,0x08},//特
};

unsigned char disp2[4][8]={
{0x10,0x10,0x1F,0x10,0x00,0x00,0x00,0x00},//中
{0x08,0x08,0x09,0x01,0x02,0x04,0x08,0x10},//贝
{0x1F,0x11,0x11,0x7F,0x02,0x11,0x20,0x40},//斯
{0x0E,0x78,0x28,0x08,0x08,0x08,0x08,0x08},//特
};

void setup(){
  pinMode(cs,OUTPUT);
  pinMode(clk,OUTPUT);
  pinMode(din,OUTPUT);
  Init_MAX7219();
}
void loop(){
  char i,j;
//Write_Max7219(0x0f, 0x00); 
//Delay_xms(500);

  for(j=0;j<4;j++)
  {
   for(i=1;i<9;i++){
    Write_Max7219_1(i,disp1[j][i-1]);
    Write_Max7219_2(i,disp2[j][i-1]);
    Write_Max7219_3(i,disp3[j][i-1]);
    Write_Max7219_4(i,disp4[j][i-1]);}
   delay(500);
  } 

}

void Write_Max7219_byte(char DATA)         
{
            char i;    
                digitalWrite(cs,0);                
            for(i=8;i>=1;i--)
          {                  
           digitalWrite(clk,0);
            if((DATA&0x80)>0){digitalWrite(din,1);}
            else{digitalWrite(din,0);}
            //提取最高位给DIN端口
            DATA=DATA<<1;//左移一位
            digitalWrite(clk,1);
           }                                 
}

void Write_Max7219_1(char address1,char dat1)
{ 
     digitalWrite(cs,0);
     Write_Max7219_byte(address1);           //写入地址,即数码管编号
     Write_Max7219_byte(dat1);               //写入数据,即数码管显示数字 
     digitalWrite(cs,1);                        
}

void Write_Max7219_2(char address2,char dat2)
{ 
     digitalWrite(cs,0);
     Write_Max7219_byte(address2);           //写入地址,即数码管编号
     Write_Max7219_byte(dat2);//写入数据,即数码管显示数字 
     digitalWrite(clk,1);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     digitalWrite(cs,1);

}

void Write_Max7219_3(char address3,char dat3)
{ 
     digitalWrite(cs,0);
     Write_Max7219_byte(address3);           //写入地址,即数码管编号
     Write_Max7219_byte(dat3);//写入数据,即数码管显示数字 
     digitalWrite(clk,1);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     digitalWrite(cs,1);

}

void Write_Max7219_4(char address4,char dat4)
{ 
     digitalWrite(cs,0);
     Write_Max7219_byte(address4);           //写入地址,即数码管编号
     Write_Max7219_byte(dat4);//写入数据,即数码管显示数字 
     digitalWrite(clk,1);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     Write_Max7219_byte(0x00);
     digitalWrite(cs,1);

}


void Init_MAX7219(void)
{
Write_Max7219_1(0x09, 0x00);//译码方式:BCD码
Write_Max7219_1(0x0a, 0x01);//亮度 
Write_Max7219_1(0x0b, 0x07); //扫描界限;8个数码管显示
Write_Max7219_1(0x0c, 0x01);  //掉电模式:0,普通模式:1
Write_Max7219_1(0x0f, 0x00);

Write_Max7219_2(0x09, 0x00);//译码方式:BCD码
Write_Max7219_2(0x0a, 0x01);//亮度 
Write_Max7219_2(0x0b, 0x07); //扫描界限;8个数码管显示
Write_Max7219_2(0x0c, 0x01);  //掉电模式:0,普通模式:1
Write_Max7219_2(0x0f, 0x00);

Write_Max7219_3(0x09, 0x00);//译码方式:BCD码
Write_Max7219_3(0x0a, 0x01);//亮度 
Write_Max7219_3(0x0b, 0x07); //扫描界限;8个数码管显示
Write_Max7219_3(0x0c, 0x01);  //掉电模式:0,普通模式:1
Write_Max7219_3(0x0f, 0x00);

Write_Max7219_4(0x09, 0x00);//译码方式:BCD码
Write_Max7219_4(0x0a, 0x01);//亮度 
Write_Max7219_4(0x0b, 0x07); //扫描界限;8个数码管显示
Write_Max7219_4(0x0c, 0x01);  //掉电模式:0,普通模式:1
Write_Max7219_4(0x0f, 0x00);//显示测试:1;测试结束,正常显示:0
delay(500); 
}

下面的视频是上次打绝地求生被放鸽子,我就改了下文字传抖音上去了。。

9. 相关下载
百度网盘:点我下载

未经允许不得转载:Arduino-Maker » 8*8点阵 16*16点阵 级联模块 示例教程 适用于Arduino平台

支付宝扫码打赏 微信打赏

原创文章,若帮到您,欢迎打赏

分享到:更多 ()

评论 2

评论前必须登录!

 

  1. #2

    怎么不显示”国”字

    极电科技工作室2年前 (2017-08-08)
  2. #1

    国字好像取模的不对,您重新取一下看。

    arron2年前 (2017-08-16)

线上商城

中贝斯特创客空间蘑菇云创客教育